background image

Parts List

 06-236115-001

7-1

October 2014

 

CHAPTER 7

 PARTS LIST

7-1

INTRODUCTION AND PARTS LIST

The table below, and on the following pages, provides a complete list of the Kidde Fire Systems

ECS Fire Suppression System with HFC-227ea Agent parts and associated system equipment.

Equipment can be ordered as complete assemblies or as individual items. In most situations,

when ordering a system, it will be easier and more cost effective to order by assembly part

numbers.
Note: Unless otherwise noted, the parts documented in this section are UL Listed and FM Ap-

proved. For non-agency approved parts, see datasheet K-90-2075.

Table 7-1. Parts List

Nomenclature

Part Number

Original P/N

Cylinder/Valve Assemblies

10 lb STD

90-100010-001

20 lb STD

90-100020-001

40 lb STD

90-100040-001

70 lb STD

90-100070-001

125 lb STD

90-100125-001

125 lb W/LLI

90-100121-001

200 lb STD Old Style Hemispherical Head before 3/98

90-100200-001

200 lb W/LLI Old Style Hemispherical Head before 3/98

90-100201-001

200 lb STD New Style Ellipsoidal Head after 3/98

90-100200-101

200 lb W/LLI New Style Ellipsoidal Head after 3/98

90-100201-101

350 lb STD

90-100350-001

350 lb W/LLI

90-100351-001

600 lb STD old style supplied before 9/01 (discontinued)

90-100600-001

600 lb W/LLI old style supplied before 9/01 (discontinued)

90-100601-001

600 lb STD new style supplied after 9/01

90-100600-100

600 lb W/LLI new style supplied after 9/01

90-100601-100

900 lb STD

90-100900-001

900 lb W/LLI

90-100901-001

(STD=Standard Cylinder Assembly, W/LLI=Cylinder with liquid level indicator)

Flexible Discharge Hoses

10-125 lb Cylinders

WK-283898-000

283898

200-350 lb Cylinders

WK-283899-000

283899

600 lb Cylinders (old style supplied before 9/01)

WK-283900-000

283900

600 lb Cylinders (new style after 9/01)

06-118225-001

900 lb Cylinders

06-118225-001

Summary of Contents for ECS






















































































































































































































Reviews:

Related manuals for ECS