PROGRAMMING HD RADIO
NOTE:
It is necessary to re-fl ash your HD radio before installation of this kit. If you do not have the Techno Research Centurion program software you may purchase a Kicker TRHDP Radio
Flash Programmer.
GETTING STARTED
1. Remove the seat and disconnect both negative and positive battery terminals.
2. Remove the windshield.
3. Remove the outer fairing.
a. Remove the four mounting screws, unplug the headlamp and set aside on a soft cloth.
4. Remove the fuel tank.
a. Unplug the fuel fi tting on the left side of the tank. You may remove the console if you want to retain vent line routing and connector placement.
b. Remove all four mounting bolts and carefully lift the tank off the bike and set aside.
5. Remove wire caddy cover.
a. Carefully release each tab along the caddy until it lifts completely.
SPEAKER INSTALLATION
6. Remove one of the white speaker pods from the inner fairing.
(Fig. 1)
a. There are fi ve fasteners in the center portion and three on the outside to release it from the inner fairing.
7. Remove the stock speaker and replace with the PSC652 speaker from the kit.
a. Install the provided speaker ring adapter onto the speaker pod.
(Fig. 2)
b. Install the speaker into the pod and fasten with the original speaker screws.
(Fig. 3)
8. Reinstall the pod to the inner fairing.
9. Repeat for the other side.
AMP INSTALLATION
If you have a 2020 Street or Tri Glide, the following steps must be completed before amplifi er installation:
Remove four screws from the HD Connect Module. Remove Module from Bracket. Relocate Module to the clutch side of the radio and secure with two 8” zip ties included.
(Fig. 4
and
Fig 5.)
NOTE:
There may be some connectors that will need to be relocated off of the radio chassis for the amp bracket to fi t.
10. Fasten the amplifi er to the bracket with the supplied hardware.
a. Insert the bolts through the bottom of the bracket and install the locknuts to the amplifi er.
11. At this time, it is highly recommended to set the amp gain setting to 0. KICKER recommends that the dip switches be set up as follows
(Fig 6)
:
Auto turn-on - 12V
Input level - HI
Amp1: HI-PASS – 80 Hz
Input Gain control – 0
Fader - ON
Amp2: HI-PASS – 60 Hz (6x9)
80 Hz (6.5” Tour Pack)
12. After fi nishing System Setup, use the supplied ¼” hardware and fasten the amp/bracket assembly to the radio chassis with the 10-pin connector and power connector facing the throttle
side.
(Fig. 7)
HARNESS INSTALLATION
13. Plug the harness into the amplifi er and route the speaker wires to their respective locations.
(Fig. 8)
a. Separate the speaker connectors and plug in the amplifi er harness to each speaker.
14. Plug the 4-pin male, rear audio connector into the 4-pin female rear audio signal connector coming from the radio harness.
(Fig. 9
and
Fig. 10)
15. Plug the switched power harness into the 2-pin amp connector on the throttle side of the fairing.
(Fig. 11)
16. Plug the blue wire on the kicker harness into the switched power harness lead with one wire.
a. This allows for an accessory 12V port to remain available.
17. Route the power leads along the clutch side of the frame neck, in the electrical caddy to the seat area.
(Fig. 12)
NOTE:
If you are not running rear speaker lids or tour pack, please plug in the Dummy Load Plug into the amplifi ed rear speaker output at the end of the harness.
(Figs. 13, 14, 15)
18. Reconnect the battery terminals and pull the excess harness slack back into the fairing. Create a slack loop with excess harness slack.
19. Plug the radio in, and set the gain.
20. Test component function and set the gain to optimize system performance.
21. Carefully reassemble the motorcycle and enjoy your new audio kit!
46HDS144
Motorcycle Audio Kit Installation Guide for Harley Davidson
®
Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes
2014–Newer (FLHT)
Package Contents:
(1) Install Guide
(1) Wiring Harness
(4) Black Cable Ties
(2) 6-1/2” KICKER Speakers & Grilles
(4) 8-32 x 1/2” Button Head Bolts
(1) Stainless Steel Mounting Bracket
(1) 75W x 4 KICKER Amp
(4) 8-32 Nylock Nuts
(1) Mounting Hardware
(3) 1/4” 20 washers
(3) 1/4” 20 1” bolts
(3) 1/4” 20 Nylock Nuts
(1) Dummy Load Plug
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit
may not
be compatible with some aftermarket head units.
FRONT KIT PROGRAMMING WITH KICKER TRHDP
Follow instructions included with KICKER TRHDP
FRONT & REAR KIT PROGRAMMING WITH KICKER TRHDP
Follow instructions included with KICKER TRHDP
