Date Issued: 09/26/17
IS-11304LED-CB
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
4) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raised dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector. (Not pro
-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
5) Make wire connections. Reference chart below for correct con
-
nections and wire accordingly.
6) Carefully push wire connections
[4]
back into outlet box making
sure all connections remain secure.
7) Secure the backpan to the outlet box with the supplied mount
-
ing screws
[3].
8) Anchor the backpan to the wall using the set of holes at each
end of fixture using the provided wood screws
[5]
and plastic
anchors
[6].
9) Slide end caps
[7]
over glass
[8]
and secure in place to backpan
using lock-up knobs
[9].
AVERTISSEMENT :
This fixture is intended for installation in accordance with the
National Electrical Code (NEC) and all local code specifications.
If you are not familiar with code requirements, installation by a
certified electrician is recommended.
DIMMING :
This LED fixture is compatible with electronic low voltage dimmers
only.
FCC INFORMATION :
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following mea
-
sures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Instructions
1) At the center of the backpan
[1]
are knockout slots. Remove
the set that matches your outlet box
[2].
2) Position the backpan over the outlet box. Secure the backpan
to the outlet box using mounting strap screws
[3]
provided
(these are the shorter of the two screws).
3) Mark the location of the outer keyhole slots of the backpan to
the wall. Be sure to mark only the narrow part of the keyhole
slot. Remove the backpan from the wall. Drill the holes using
an appropriately sized drill bit. Insert the provided anchors
[6]
into the holes.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
2
3
4
5
6
1
7
8
9
