manualshive.com logo in svg

KIC start, User Manual

Share
Download
KIC start User Manual Download Page 10

KICstart  

Version 

1.1.0.x 

KICstart User Manual 

 

3 

KICstart Hardware 

Inventory 

Part Description 

KIC Part Number 

KICstart Data logger (6 channel)

 

 KICSTART-06  

Communication Cable

 

 CB-RS232-15 

Thermal Shield 

 TS-SL-18 

Individual Color Coded Thermocouples  

 TC-TK-06-36 

Aluminum Tape and Hi-temp Solder for attaching Thermocouples

 

 TAPE 

KICstart User Manual, KICstart software

 

 MAN-KS-V2 

 
 

KICstart Configuration 

The 

KIC

start

 – Datalogger 

will be plugged in directly to the 

computer COM port using the communication cable. 
 
 

KICstart Sample rates 

KICstart PROM Version 7.0 

Application Type 

Samples/Sec 

Solder Reflow  

4 

Wave Solder 

10 

Cure  

3 

Semiconductor 

4 

 
 
The 

KIC

start sample rates will vary depending on the selected 

Application

 type. 

 
 

KICstart Maintenance: Changing the Battery 

 

 

 

 

 

 
To install or change the battery or for calibration of the 

KICstart

 profiler you will have to unscrew the 

battery cover from the bottom side of the 

KICstart

.  This will require a small Flathead screwdriver.  The 

screw has a retaining clip to keep it in place so it will not come all the way out.  Just loosen it enough so the 
cover comes free.  Remove the battery cover.  There is a white connector for a 9-volt battery.  Once you 
have connected the battery, slip the battery back in, placing the connector end in first.  Then replace the 
cover and tighten the battery cover.   See the 

KICstart

 hardware section of this manual for calibration 

details,

 

page 43. 

 
 
 

Summary of Contents for start


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands