manualshive.com logo in svg

Kia Telluride 2023, Manual, Page: 134 / 524

Share
Download
Kia Telluride 2023 Manual Download Page 134

Features of your vehicle

52

4

Dual Wide Sunroof

NOTICE

Do not use diesel to refuel vehicles with 
a gasoline engine.

NOTICE

Do not switch on the ignition if you acci

-

dentally refuel with the wrong fuel. Oth

-

erwise, fuel can enter the fuel system.
Even small amounts of the wrong fuel 
could result in damage to the fuel sys

-

tem and the engine. Have the system 
serviced by an authorized Kia dealer.

NOTICE

Do not overfill the fuel tank

Do not overfill the fuel tank; otherwise 
fuel may slide, causing harm to the envi

-

ronment and damaging the vehicle.

Dual Wide Sunroof (if 
equipped)

If your vehicle is equipped with a sun

-

roof, you can slide or tilt your sunroof 
with the sunroof switch located on the 
overhead console.

[A]: Front, [B]: Rear
The sunroof can only be operated when 
the ENGINE START/STOP button is in 
the ON or START position.
The sunroof can be operated for 
approximately 3 minutes after the 
ENGINE START/STOP button is in the 
ACC or OFF position. However, if the 
front door is open, the sunroof cannot 
be operated even within the 3 minutes 
period.

WARNING

僅 Adjust the sunroof or sunshade when 

your vehicle stops. This could result in 
loss of control and an accident that 
may cause injury, or property dam

-

age.

僅 Do not leave the engine running and 

the key in your vehicle with unsuper

-

vised children. Unattended children 
could operate the sunroof, which 
could result in serious injury.

僅 Do not sit on the top of the vehicle. It 

may cause injury or vehicle damage.

OON042077

Summary of Contents for Telluride 2023













































































































































































































































































































































































































































































































































Reviews:

No comments