manualshive.com logo in svg

Kia Stinger 2019, Owner'S Manual, Page: 486 / 671

Share
Download
Kia Stinger 2019 Owner'S Manual Download Page 486

30

6

What to do in an emergency

Notes on the safe use of the
Tyre Mobility Kit

• Park your car at the side of the

road so that you can work with the
Tyre Mobility Kit away from moving
traffic. Place your warning triangle
in a prominent place to make pass-
ing vehicles aware of your location.

• To be sure your vehicle will not

move, even when you're on fairly
level ground, always set your park-
ing brake.

• Only use the Tyre Mobility Kit for

sealing/inflation passenger car
tyres. Do not use on motorcycles,
bicycles or any other type of tyres.

• Do not remove any foreign objects-

such as nails or screws -that have
penetrated the tyre.

• Before using the Tyre Mobility Kit,

read the precautionary advice
printed on the sealant bottle!

• Provided the car is outdoors, leave

the engine running. Otherwise
operating the compressor may
eventually drain the car battery.

• Never leave the Tyre Mobility Kit

unattended whilst it is being used.

• Do not leave the compressor run-

ning for more than 10 min. at a time
or it may overheat.

• Do not use the Tyre Mobility Kit if

the ambient temperature is below
-30°C (-22°F).

• When the tyre and wheel are dam-

aged, do not use Tyre Mobility Kit
for your safety.

WARNING

Do not use the Tyre Mobility Kit
if a tyre is severely damaged by
driving run flat or with insuffi-
cient air pressure.
Only punctured areas located
within the tread region of the
tyre can be sealed using the
Tyre Mobility Kit.

Summary of Contents for Stinger 2019
































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments