manualshive.com logo in svg

Kia Stinger 2019, Owner'S Manual, Page: 125 / 671

Share
Download
Kia Stinger 2019 Owner'S Manual Download Page 125

20

4

Features of your vehicle

Non-power tailgate

Opening the tailgate

• The tailgate is locked or unlocked

when all doors are locked or
unlocked with the smart key or
central door lock/unlock switch.

• Only the tailgate is unlocked if the

tailgate unlock button on the smart
key is pressed for approximately 1
second.

• If unlocked, the tailgate can be

opened by pressing the handle and
pulling it up.

• Once the tailgate is opened and

then closed, the tailgate locks auto-
matically. (All doors must be locked.)

✽

✽

NOTICE

In cold and wet climates, door lock
and door mechanisms may not work
properly due to freezing conditions.

TAILGATE

OCK047016

WARNING

- 

Rear cargo
area

Occupants should never ride in
the rear cargo area where no
restraints are available. To avoid
injury in the event of an acci-
dent or sudden stops, occu-
pants should always be proper-
ly restrained.

WARNING

- 

Exhaust
fumes

If you drive with the tailgate
opened, you will draw dangerous
exhaust fumes into your vehicle
which can cause serious injury
or death to vehicle occupants.
If you must drive with the tail-
gate opened, keep the air vents
and all windows open so that
additional outside air comes
into the vehicle.

WARNING

The tailgate swings upward.
Make sure no objects or people
are near the rear of the vehicle
when opening the tailgate.

Summary of Contents for Stinger 2019
































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments