manualshive.com logo in svg

Kia Sorento 2003, Manual, Page: 286 / 1349

Share
Download
Kia Sorento 2003 Manual Download Page 286

INSPECTION 

1. Be sure there is no play in the fuse holders, and that the fuses are held 

securely. 

2. Are the fuse capacities for each circuit correct? 

3. Are there any blown fuses? 

If a fuse is to be replaced, be sure to use a new fuse of the same 
capacity. Always determine why the fuse blew first and completely 
eliminate the problem before installing a new fuse. 

 

 

Never use a fuse of higher capacity than specified. 

 

INSPECTION OF FUSES 

1. Prior to replacing the fuse with a new one, check the circuit for a short 

and the related parts for abnormal conditions. Only after the correction of 
a short or replacement of abnormal parts, should a fuse with the same 
ampere rating be installed. 

 

Normally, this type of problem occurs after a fairly long period of use, 

FUSES AND RELAY

FUSES

Summary of Contents for Sorento 2003






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments