Home
/
Kia
/
SELTOS
/
Manual

Kia SELTOS, Manual, Page: 177 / 280

Share

Page: 177 / 280

Kia SELTOS Manual Download Page 177

85

4

4

Features of your vehicle

Rear View Monitor (RVM)

Rear View Monitor (RVM) (if
equipped)

Rear View Monitor is a supplemental
function that shows the area behind
the vehicle on the infotainment
function to assist you when parking
or backing up.

Rear View Monitor with parking
guidance will activate when the
engine is running and the shift lever
is in the R (Reverse) position.

WARNING

䳜 This function is a supplementary

function only. It is the responsibil

-

ity of the driver to always check

the inside/outside rear view mir

-

ror and the area behind the vehi

-

cle before and whilst backing up
because there is a dead zone that
can't be seen through the camera.

䳜 If the camera lens is covered with

foreign material, Rear View Moni

-

tor may not operate normally.
Always keep the camera lens
clean.
However, do not use chemical sol

-

vents such as strong detergents
containing high alkaline or volatile
organic solvents (petrol, acetone
etc.). This may damage the cam

-

era lens

Driving Rear View (DRV) function (if
equipped)

Rear view whilst driving is a driving
assist function that shows the
image behind the vehicle on the
screen regardless of vehicle speed
whilst driving.

OSP2071096L

OSP2041029R

OSP2049091R

«
...
175
176
177
178
179
...
»

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments