Kia SELTOS Manual Download Page 145

Page: 145 / 280

Features of your vehicle

Instrument cluster

Outside temperature gauge

This gauge indicates the current
outside air temperatures by 1 C (1

F).

䳜 Temperature range: -40 C ~ 85

C (-40 F ~ 211 F)

The outside temperature on the
display may not change immedi

ately like a general thermometer to
prevent the driver from being inat

tentive.

To change the temperature unit
(from C to F or from F to C)

The temperature unit can be
changed by using the "User set

tings" mode of the LCD Display.

* For more details, refer to "LCD dis

play" on page 4-55.

Transmission shift indicator

Transmission shift indicator displays
gear information depending on your
vehicle's transmission type.

Automatic transmission/intelligent
variable transmission shift indica

tor (if equipped)

This indicator displays which auto

matic transmission/intelligent vari

able transmission shift lever is
selected.
䳜 Park: P
䳜 Reverse: R
䳜 Neutral: N
䳜 Drive: D

Manual shift mode
䳜 Shifting up: ▲2, ▲3, ▲4, ▲5, ▲6
䳜 Shifting down: ▼1, ▼2, ▼3, ▼4,

▼5

OSP2049106

OSK3048128NR

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 145 / 280

Search results

Summary of Contents for SELTOS

Reviews: