manualshive.com logo in svg

Kia SELTOS, Manual, Page: 139 / 280

Share
Download
Kia SELTOS Manual Download Page 139

47

4

4

Features of your vehicle

Mirrors

CAUTION

䳜 The mirrors stop moving when 

they reach the maximum adjust

-

ing angles, but the motor contin

-

ues to operate whilst the switch is 
pressed. Do not press the switch 
longer than necessary, the motor 
may be damaged.

䳜 Do not attempt to adjust the out

-

side rear view mirror by hand. 
Doing so may damage the parts.

Folding the outside rear view mir

-

ror (if equipped)

The outside rear view mirror can be 
folded or unfolded by pressing the 
switch when the ignition switch or 
ENGINE START/STOP button is in 
the ON position as below.

䳜 To fold the outside rear view mir

-

ror depress the button (1).

䳜 To unfold it, depress the button 

(1) again.

CAUTION

The electric type outside rear view 
mirror operates even though the 
ignition switch or ENGINE START/
STOP button is in the LOCK or OFF 
position. However, to prevent 
unnecessary battery discharge, do 
not adjust the mirrors longer than 
necessary whilst the engine is not 
running.

CAUTION

In case it is an electric type outside 
rear view mirror, don't fold it by 
hand. It could cause motor failure.

OSP2049446R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments