manualshive.com logo in svg

Kia SELTOS, Manual, Page: 134 / 280

Share
Download
Kia SELTOS Manual Download Page 134

Features of your vehicle

42

4

Steering wheel

䳜 If the Electronic Power Steering 

System does not operate nor

-

mally, the warning light will illumi

-

nate on the instrument cluster. 
The steering wheel may become 
difficult to control or operate 
abnormally. In this case, have the 
system inspected by a profes

-

sional workshop. Kia recom

-

mends to visit an authorised Kia 
dealer/service partner.

䳜 When you operate the steering 

wheel in low temperature, abnor

-

mal noise could occur. If tempera

-

ture rises, the noise will disappear. 
This is a normal condition.

Tilt & telescopic steering wheel

A tilt and telescopic steering wheel 
allows you to adjust the steering 
wheel before you drive. You can also 
raise it to give your legs more room 
when you exit and enter the vehicle.

The steering wheel should be posi

-

tioned so that it is comfortable for 
you to drive, whilst permitting you 
to see the instrument panel warning 
lights and gauges.

WARNING

䳜 Never adjust the angle of the 

steering wheel whilst driving. You 
may lose steering control and 
cause severe personal injury, 
death or accidents.

䳜 After adjusting, push the steering 

wheel both up and down to be 
certain it is locked in position.

Adjusting steering wheel angle and 
height

1. To change the steering wheel 

angle, pull down the lock release 
lever (1).

2. Adjust the steering wheel to the 

desired angle (2) and height (3, if 
equipped).
Move the steering wheel, so it 
points toward your chest, not 
toward your face. Make sure you 
can see the instrument panel 
warning lights and gauges. After 
adjusting, pull up the lock.

3. Pull up the lock-release lever to 

lock the steering wheel in place.
Push the steering wheel both up 
and down to be certain it is locked 
in position.

4. Be sure to adjust the steering 

wheel to the desired position 
before driving.

OSP2041011R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments