manualshive.com logo in svg

Kia SELTOS, Manual, Page: 132 / 280

Share
Download
Kia SELTOS Manual Download Page 132

Features of your vehicle

40

4

Sunroof

䳜 When the 12 volt battery is either 

disconnected or discharged

䳜 When the sunroof fuse is replaced
䳜 If the sunroof one-touch AUTO 

OPEN/CLOSE operation is not 
functioning properly

Sunroof resetting procedure:
1. It is recommended to perform the 

reset procedure with the vehicle 
engine running. Start the vehicle 
in P (Park).

2. Make sure the sunroof glass is in 

the fully closed position. If the 
sunroof glass is open, push the 
switch forward until the sunroof 
glass is fully closed.

3. Release the switch when the sun

-

roof glass is fully closed.

4. Push the switch forward until the 

sunroof glass moves slightly. 
Then release the switch.

5. Within 3 seconds, push and hold 

the sunroof switch forward until 
the sunroof glass slides open and 
close. Do not release the switch 
until the operation is completed. If 
you release the switch during 
operation, start the procedure 
again from step 2.

NOTICE

If the sunroof does reset when the 
vehicle battery is disconnected or 
discharged, or the sunroof fuse is 
blown, the sunroof may not operate 
normally.

Sunroof open warning

If the driver turns off the engine 
when the sunroof is not fully closed, 
the warning chime will sound for 
several seconds and the sunroof 
open warning will appear on the 
cluster LCD display.

Close the sunroof securely when 
leaving your vehicle.

CAUTION

Make sure the sunroof is closed fully 
when leaving your vehicle. If the 
sunroof is left open, rain or snow 
may wet the interior of the vehicle. 
Also, leaving the sunroof open when 
the vehicle is unattended may invite 
theft.

OSP2049103

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments