manualshive.com logo in svg

Kia SELTOS, Manual, Page: 130 / 280

Share
Download
Kia SELTOS Manual Download Page 130

Features of your vehicle

38

4

Sunroof

NOTICE

The sunroof glass cannot slide open 
and tilt open at the same time. You 
cannot tilt open whilst the sunroof 
glass is slide open, and you cannot 
slide open whilst the sunroof is tilt 
open. Slide open or tilt open with the 
sunroof glass when the sunroof 
glass is completely closed.

Slide open/close

䳜 Push the sunroof switch rear

-

ward, the sunshade and sunroof 
glass will slide open. Push the 
sunroof switch forward, only the 
sunroof glass will close.

䳜 Push the sunroof switch forward 

or rearward to the first detent 
position, the sunroof glass will 
operate manually. 
Push the sunroof switch forward 
or rearward to the second detent 
position, the sunroof glass will 
operate automatically (auto slide 
feature).

To stop the sunroof movement at 
any point, push the sunroof switch 
in any direction.

NOTICE

To reduce wind noise whilst driving, 
we recommend you to drive at the 
recommended position before the 
maximum slide open position.

Automatic reversal

If the sunroof senses any obstacle 
whilst it is closing automatically, it 
will reverse direction then stop at a 
certain position.

The auto reverse function may not 
work if an object thin or soft is 
caught, or the sunroof is closed 
manually.

OSP2N041042

OSP2I041451

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments