manualshive.com logo in svg

Kia SELTOS, Manual, Page: 110 / 280

Share
Download
Kia SELTOS Manual Download Page 110

Features of your vehicle

18

4

Door locks

CAUTION

Be careful not to damage the cover 
whilst removing it or misplace it 
after removing it.

NOTICE

䳜 In cold and wet climates, door lock 

and door mechanisms may not 
work properly due to freezing 
conditions.

䳜 If the door is locked/unlocked 

multiple times in rapid succession 
with either the vehicle key or door 
lock switch, the system may stop 
operating temporarily in order to 
protect the circuit and prevent 
damage to system components.

WARNING

䳜 If you don't close the door 

securely, the door may open 
again.

䳜 Be careful that someone's body 

and hands are not trapped when 
closing the door.

WARNING

If people must spend a longer time 
in the vehicle whilst it is very hot or 
cold outside, there is risk of injuries 
or danger to life. Do not lock the 
vehicle from the outside when there 
are people in it.

CAUTION

Do not frequently repeat opening 
and closing of doors, or apply exces

-

sive force to a door whilst the door 
closer is operating.

Operating door locks from inside 
the vehicle

You can operate door locks with the 
door lock handle or central door lock 
switch.

With the door handle

䳜 Front door

If the inner door handle (1) is 
pulled when the door is locked, 
the door will unlock and open.

䳜 Rear door

If the inner door handle is pulled 
once when the door is locked, the 
door will unlock.
If the inner door handle is pulled 
once more, the door will open.

OSP2049004R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments