Kia SELTOS Manual Download Page 11

Page: 11 / 280

Introduction

Vehicle break-in process

By following a few simple precau

tions for the first 1,000 km (600
miles) you may add to the perfor

mance, economy and life of your
vehicle.
䳜 Do not race the engine.
䳜 Whilst driving, keep your engine

speed (rpm, or revolutions per
minute) between 2,000 rpm and
4,000 rpm.

䳜 Do not maintain a single speed for

long periods of time, either fast or
slow. Varying engine speed is
needed to properly break-in the
engine.

䳜 Avoid hard stops, except in emer

gencies, to allow the brakes to
seat properly.

䳜 Don't tow a trailer during the first

2,000 km (1,200 miles) of opera

tion.

䳜 Fuel economy and engine perfor

mance may vary depending on
vehicle break-in process and be
stabilized after 6,000 km (4,000
miles). New engines may con

sume more oil during the vehicle
break-in period.

Returning used vehicles (for
europe)

Kia promotes an environmentally
sound treatment for end of life
vehicles and offers to take back
your Kia end of life vehicles in accor

dance with the European Union (EU)
End of Life Vehicles Directive.

You can get detailed information
from your national Kia homepage.

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 11 / 280

Search results

Summary of Contents for SELTOS

Reviews: