Kia SELTOS Manual Download Page 104

Page: 104 / 280

Features of your vehicle

Smart key

The button will only operate when
the smart key is within 0.7~1 m
(28~40 inches) from the front driver
side door handle.

When the smart key is recognised in
the area of 0.7~1 m (28~40 inches)
from the front driver side door han

dle, other people can also open the
door without possession of the
smart key.

After pressing the button, the doors
will lock automatically unless you
open any door within 30 seconds.

Tailgate open

If you press the button for longer
than a second, the lock will be
released or the lift gate will be
opened according to the options of
the vehicle.

Once the tailgate is opened and then
closed, the tailgate will lock auto

matically.

Smart key precautions

NOTICE

䳜 If, for some reason, you happen to

lose your smart key, you will not
be able to start the engine. Tow
the vehicle, if necessary, contact a
professional workshop. Kia rec

ommends to contact an autho

rised Kia dealer/service partner.

䳜 A maximum of 2 smart keys can

be registered to a single vehicle. If
you lose a smart key, Kia recom

mends to contact an authorised
Kia dealer/service partner.

䳜 The smart key will not work if any

of the following occurs:
- The smart key is close to a

radio transmitter such as a
radio station or an airport
which can interfere with normal
operation of the smart key.

- The smart key is near a mobile

two-way radio system or a
mobile phone.

- Another vehicle's smart key is

being operated close to your
vehicle.
When the smart key does not
work properly, open and close
the door with the mechanical
key. If you have a problem with
the smart key, Kia recommends
to contact an authorised Kia
dealer/service partner.

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 104 / 280

Search results

Summary of Contents for SELTOS

Reviews: