manualshive.com logo in svg

Kia SELTOS, Manual, Page: 72 / 280

Share
Download
Kia SELTOS Manual Download Page 72

Safety features of your vehicle

50

3

Air bag - supplemental restraint system

goes off after approximately 60 
seconds.

Passenger䳓s front air bag OFF indi

-

cator

The passenger䳓s front air bag 
OFF indicator illuminates for 

about 4 seconds after the ignition 
switch is turned to the ON position.

The passenger䳓s front air bag OFF 
indicator also comes on when the 
passenger䳓s front air bag ON/OFF 
switch is set to the OFF position and 
goes off when the passenger䳓s front 
air bag ON/OFF switch is set to the 
ON position.

CAUTION

If the passenger䳓s front air bag ON/
OFF switch malfunctions, the pas

-

senger䳓s front air bag OFF indicator 
will not illuminate (The passenger's 
front air bag ON indicator comes on 
and goes off after approximately 60 
seconds) and the passenger䳓s front 
air bag will inflate in a frontal impact 

even if the passenger䳓s front air bag 
ON/OFF switch is set to the OFF 
position.
In this case, have the passenger's 
front air bag ON/OFF switch and the 
SRS air bag system inspected by a 
professional workshop.
Kia recommends to visit an autho

-

rised Kia dealer/service partner.

SRS components and functions

* The actual position of SRS compo

-

nents may differ from the illus

-

tration.

The SRS consists of the following 
components:
1. Driver's front air bag module
2. Passenger's front air bag module
3. Side air bag modules*
4. Curtain air bag modules*
5. Retractor pre-tensioner assem

-

blies*

6. Air bag warning light
7. SRS control module (SRSCM)/ roll

-

over sensor*

OSP2031064L

OSP2039068R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments