manualshive.com logo in svg

Kia SELTOS, Manual, Page: 30 / 280

Share
Download
Kia SELTOS Manual Download Page 30

Safety features of your vehicle

8

3

Seat

CAUTION

䳜 The power seat is driven by an 

electric motor. Stop operating 
once the adjustment is com

-

pleted. Excessive operation may 
damage the electrical equipment.

䳜 When in operation, the power 

seat consumes a large amount of 
electrical power. To prevent 
unnecessary charging system 
drain, don't adjust the power seat 
longer than necessary whilst the 
engine is not running.

䳜 Do not operate two or more 

power seat control switches at 
the same time. Doing so may 
result in power seat motor or 
electrical component malfunction.

Moving forward and backward

To move the seat forward or back

-

ward:
1. Push the control switch forward 

or rearward to move the seat to 
the desired position.

2. Release the switch once the seat 

reaches the desired position.

Reclining seatback

To recline the seatback:
1. Push the control switch forward 

or rearward to move the seatback 
to the desired angle.

2. Release the switch once the seat 

reaches the desired position.

Adjusting seat cushion tilt and 
height

To adjust the height of the seat:
1. Pull the front portion of the con

-

trol switch up to raise or press 

OSP2039005R

OSP2039006R

OSP2039007R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments