Kia SELTOS Manual Download Page 29 | Manualshive

Page: 29 / 280

Kia SELTOS Manual Download Page 29

7

3

3

Safety features of your vehicle

Seat

lever. If the seat moves, it is not
locked properly.

Reclining seatback

To recline the seatback:
1. Lean forward slightly and lift up

the seatback recline lever.

2. Carefully lean back on the seat

and adjust the seatback of the
seat to the position you desire.

3. Release the lever and make sure

the seatback is locked in place.
(The lever MUST return to its
original position for the seatback
to lock.)

Adjusting seat height

To adjust the height of the seat,
push the lever upwards or down

-

wards.
䳜 To lower the seat height, push

down the lever several times.

䳜 To raise the seat height, pull up

the lever several times.

Front seat adjustment for power
seat (if equipped)

The driver's seat can be adjusted by
using the control switches located
on the outside of the seat cushion.
Before driving, adjust the seat to
the proper position so as to easily
control the steering wheel, pedals
and switches on the instrument
panel.

WARNING

The power seat is operable with the
ignition OFF.
Therefore, children should never be
left unattended in the car.

OSP2039003R

OSP2039004R

«
...
27
28
29
30
31
...
»

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments