manualshive.com logo in svg

Kia SELTOS, Manual, Page: 241 / 280

Share
Download
Kia SELTOS Manual Download Page 241

149

4

4

Features of your vehicle

Exterior features

2. Whilst lifting the cover up, hold 

the area near the front slots. 
Then, pull up the cover at approx

-

imately 45   angle.

WARNING

Do not place objects on the cargo 
area cover. Such objects may be 
thrown about inside the vehicle and 
possibly injure vehicle occupants 
during an accident or when braking.

CAUTION

Since the cargo area cover may be 
damaged or malformed, do not put 
luggage on it when it is used.

Exterior features

Roof rack (if equipped)

If the vehicle has a roof rack, you 
can load cargo on top of your vehi

-

cle.

Crossbars and fixing components 
needed to install the roof rack on 
your vehicle may be obtained from 
an authorised Kia dealer/service 
partner or other qualified shop.

NOTICE

䳜 The crossbars (if equipped) should 

be placed in the proper load car

-

rying positions prior to placing 
items onto the roof rack.

䳜 If the vehicle is equipped with a 

sunroof, be sure not to position 
cargo onto the roof rack in such a 
way that it could interfere with 
sunroof operation.

䳜 When the roof rack is not being 

used to carry cargo, the crossbars 

OSP2049061

OSP2049064L

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments