Kia SELTOS Manual Download Page 223

Page: 223 / 280

131

Features of your vehicle

Windscreen defrosting and defogging

grill to improve heater and
defroster efficiency and to reduce
the probability of fogging up the
inside of the windscreen.

Defogging inside windscreen with
manual climate control system

1. Select any fan speed except "0"

position.

2. Select desired temperature.
3. Select the

position.

4. The outside (fresh) air and air

conditioning will be selected auto

matically.

If the air conditioning and outside
(fresh) air position are not selected
automatically, press the corre

sponding button manually.

Defrosting outside windscreen with
manual climate control system

1. Set the fan speed to the highest

(extreme right) position.

2. Set the temperature to the

extreme hot position.

3. Select the

position.

4. The outside (fresh) air and air

conditioning will be selected auto

matically.

Defogging inside windscreen with
the automatic climate control

1. Set the fan speed to the desired

position.

2. Select desired temperature.
3. Press the defroster button (

OSP2049316

OSP2049317

OSP2049318

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 223 / 280

Search results

Summary of Contents for SELTOS

Reviews: