manualshive.com logo in svg

Kia SELTOS, Manual, Page: 217 / 280

Share
Download
Kia SELTOS Manual Download Page 217

125

4

4

Features of your vehicle

Automatic climate control system

Heating and air conditioning auto

-

matically

1. Press the AUTO button.

The modes, fan speeds, air intake 
and air-conditioning will be con

-

trolled automatically by setting 
the temperature.

2. Turn the temperature control 

switch to the desired tempera

-

ture.

NOTICE

䳜 To turn the automatic operation 

off, select any button or switch of 
the following:
- Mode selection button
- Air conditioning button

- Front windscreen defroster 

button (Press the button one 
more time to deselect the front 
windscreen defroster function. 
The AUTO sign will illuminate on 
the information display once 
again.)

- Fan speed control knob
The selected function will be con

-

trolled manually whilst other 
functions operate automatically.

䳜 For your convenience and to 

improve the effectiveness of the 
climate control, use the AUTO 
button and set the temperature 
to 22  C (72  F).

NOTICE

Never place anything over the sen

-

sor located on the instrument panel 
to ensure better control of the 
heating and cooling system.

OSP2049322R

OSP2049323R

OSP2041468R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments