Kia SELTOS Manual Download Page 208

Page: 208 / 280

Features of your vehicle

116

Climate control system

side through the heating and air
conditioning system.

A: Outside air

B: Recirculated air

C: Climate control air filter

D: Blower

E: Evaporator core

F: Heater core

If dust or other pollutants accumu

late in the filter over a period of
time, the air flow from the air vents
may decrease. This leads to mois

ture accumulating on the inside of
the windscreen even when the out

side (fresh) air position is selected. If
this happens, have the climate con

trol air filter replaced by a profes

sional workshop. Kia recommends to
visit an authorised Kia dealer/ser

vice partner.

NOTICE

䳜 Replace the filter according to the

Maintenance Schedule. If the

vehicle is being driven in severe
conditions such as dusty or rough
roads, more frequent air condi

tioner filter inspections and
changes are required.

䳜 When the air flow rate suddenly

decreases, have the system
checked by a professional work

shop. Kia recommends to visit an
authorised Kia dealer/service
partner.

Air conditioning refrigerant label

Example

* The actual air conditioning refrig

erant label in the vehicle may dif

fer from the illustration.

Each symbol and specification on
the air conditioning refrigerant label
is represented below:
1. Classification of refrigerant
2. Amount of refrigerant
3. Classification of Compressor lubri

cant

4. Caution
5. Service manual

ODEEV068230NR

OSP2069029

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 208 / 280

Search results

Summary of Contents for SELTOS

Reviews: