manualshive.com logo in svg

Kia SELTOS, Manual, Page: 193 / 280

Share
Download
Kia SELTOS Manual Download Page 193

101

4

4

Features of your vehicle

Lighting

Also, the rear fog lights turn on 
when the rear fog light switch is 
turned on after the front fog light 
switch (if equipped) is turned on and 
the headlight switch is in the 
parklight position.

To turn the rear fog lights off:
䳜 Turn the rear fog light switch to 

the on position again.

High Beam Assist (HBA) (if 
equipped)

High Beam Assist is a function that 
automatically adjusts the headlamp 
range (switches between high beam 
and low beam) according to the 
brightness of other vehicles and 
road conditions.

Type A

Type B

Function setting

The driver can activate High Beam 
Assist by placing the ignition switch 
to the ON position and by selecting: 
'User setting → Lights → HBA (High 
Beam Assist)'. If you disable this 
setting, High Beam Assist will not 
work.

The setting of High Beam Assist will 
be maintained, as selected, when 
the engine is re-started.

Operating High Beam Assist

1. Place the light switch in the AUTO 

position.

2. Turn on the high beam by pushing 

the lever away from you.

3. High Beam Assist (

) indicator 

will illuminate.

4. High Beam Assist will turn on 

when vehicle speed is above 40 
km/h (25 mph).
1)If the light switch is pushed 

away when High Beam Assist is 

OSP2049080L

OSP2049080R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments