manualshive.com logo in svg

Kia SELTOS, Manual, Page: 185 / 280

Share
Download
Kia SELTOS Manual Download Page 185

93

4

4

Features of your vehicle

Forward/Reverse Parking Distance Warning

(PDW)

Non-operational conditions of For

-

ward/Reverse Parking Distance 
Warning

Forward/Reverse Parking Distance 
Warning may not operate normally 
when:

䳜 Moisture is frozen to the sensor. 

(It will operate normally when 
moisture melts.)

䳜 Sensor is covered with foreign 

matter, such as snow or water, or 
the sensor cover is blocked. (It will 
operate normally when the mate

-

rial is removed or the sensor is no 
longer blocked.)

䳜 Sensor is stained with foreign 

matter such as snow or water. 
(Sensing range will return to nor

-

mal when removed.)

䳜 The Parking Safety button is off.

There is a possibility of Forward/
Reverse Parking Distance Warning 
malfunction when:

䳜 Driving on uneven road surfaces 

such as unpaved roads, gravel, 
bumps, or gradient.

䳜 Objects generating excessive 

noise such as vehicle horns, loud 
motorcycle engines, or truck air 
brakes can interfere with the 
sensor.

䳜 Heavy rain or water spray.
䳜 Wireless transmitters or mobile 

phones present near the sensor.

䳜 Sensor is covered with snow.

Detecting range may decrease 
when:

䳜 Outside air temperature is 

extremely hot or cold.

The following objects may not be 
recognised by the sensor:

䳜 Sharp or slim objects such as 

ropes, chains or small poles.

䳜 There are undetectable objects 

smaller than 100 cm (40 inches) 
and narrower than 14 cm (6 
inches) in diameter.

䳜 Objects, which tend to absorb 

sensor frequency such as clothes, 
spongy material or snow.

Forward/Reverse Parking Distance 
Warning precautions

䳜 The warning may not sound con

-

sistently depending on the speed 
and shapes of the objects 
detected.

䳜 Forward/Reverse Parking Dis

-

tance Warning may malfunction if 
the vehicle bumper height or sen

-

sor installation has been modified. 
Any non-factory installed equip

-

ment or accessories may also 
interfere with the sensor perfor

-

mance.

䳜 Sensor may not recognize objects 

less than 30 cm (12 inches) from 
the sensor, or it may sense an 
incorrect distance. Use with cau

-

tion.

䳜 When the sensor is frozen or 

stained with snow or water, the 

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments