manualshive.com logo in svg

Kia SELTOS, Manual, Page: 166 / 280

Share
Download
Kia SELTOS Manual Download Page 166

Features of your vehicle

74

4

Warning and indicator lights

In this case, have the vehicle 
inspected by a professional work

-

shop. Kia recommends to visit an 
authorised Kia dealer/service part

-

ner.

Anti-lock brake system (ABS) 
warning light 

This warning light illuminates:

䳜 Once you set the ignition switch 

or ENGINE START/STOP button to 
the ON position.
- It illuminates for approximately 

3 seconds and then goes off.

䳜 When there is a malfunction with 

the ABS (The normal braking sys

-

tem will still be operational with

-

out the assistance of the anti-
lock brake system).
In this case, have the vehicle 
inspected by a professional work

-

shop. Kia recommends to visit an 
authorised Kia dealer/service 
partner.

Electronic Power Steering (EPS) 
warning light 

 (if equipped)

This warning light illuminates:

䳜 Once you set the ignition switch 

or ENGINE START/STOP button to 
the ON position.
- This indicator light comes on 

after the ignition key is turned 
to the ON position and then 

goes out after approximately 3 
seconds.

䳜 When there is a malfunction with 

the EPS.
In this case, have the vehicle 
inspected by a professional work

-

shop. Kia recommends to visit an 
authorised Kia dealer/service 
partner.

Charging System Warning Light 

This warning light illuminates:

䳜 Once you set the ignition switch 

or ENGINE START/STOP button to 
the ON position.

䳜 When there is a malfunction with 

either the alternator or electrical 
charging system.

If there is a malfunction with either 
the alternator or electrical charging 
system:

1. Drive carefully to the nearest safe 

location and stop your vehicle.

2. Turn the engine off and check the 

alternator drive belt for looseness 
or breakage.
In this case, have the vehicle 
inspected by a professional work

-

shop. Kia recommends to visit an 
authorised Kia dealer/service 
partner.

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments