manualshive.com logo in svg

Kia SELTOS, Manual, Page: 164 / 280

Share
Download
Kia SELTOS Manual Download Page 164

Features of your vehicle

72

4

Warning and indicator lights

Press start button with key (for 
smart key system)

䳜 This warning message illumi

-

nates if you press the ENGINE 
START/STOP button whilst the 
warning message "Key not 
detected" is illuminating.

䳜 At this time, the immobiliser indi

-

cator light blinks.

Check Blind-Spot Collision Warning 
(if equipped)

This warning message is displayed if 
there is a problem with Blind spot 
Collision Warning. In this case, we 
recommend that you have the vehi

-

cle inspected by an authorised Kia 
dealer

* For more information, refer to 

"Blind-Spot Collision Warning 
(BCW) (if equipped)" on page 6-
121.

Warning and indicator lights

The warning light and indicator light 
indicate a situation where the driver 
should be careful and whether the 
various functions are activated.

Warning lights

The warning light indicates situa

-

tions that require the driver to pay 
attention.

NOTICE

Warning lights

Make sure that all warning lights are 
OFF after starting the engine. If any 
light is still ON, this indicates a situ

-

ation that needs attention.

Air bag warning light 

This warning light illuminates:
䳜 Once you set the ignition switch 

or ENGINE START/STOP button to 
the ON position.
- It illuminates for approximately 

6 seconds and then goes off.

䳜 When there is a malfunction with 

the SRS.
In this case, have the vehicle 
inspected by a professional work

-

shop. Kia recommends to visit an 
authorised Kia dealer/service 
partner.

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments