manualshive.com logo in svg

Kia SELTOS, Manual, Page: 160 / 280

Share
Download
Kia SELTOS Manual Download Page 160

Features of your vehicle

68

4

LCD displays

NOTICE

If any of the following conditions 
occurs, the mileage and days may 
be incorrect.
䳜 The battery cable is disconnected.
䳜 The battery is discharged.

Driving info display

At the end of each driving cycle, the 
Driving Info message is displayed.

This display shows the trip distance 
(1), average fuel economy (2), driv

-

ing time (3).

This information is displayed for a 
few seconds when you turn off the 
vehicle, and then goes off automati

-

cally. The information is calculated 
for each time the vehicle is turned 
on.

NOTICE

䳜 If sunroof open warning is dis

-

played in the cluster, the Driving 
Information message may not be 
displayed.

䳜 To set the charging time and/or 

climate time, refer to a separately 
supplied car navigation system 
manual for detailed information.

LCD display messages

Door, bonnet, tailgate, sunroof 
open

䳜 This warning is displayed indicat

-

ing which door, the bonnet, the 
tailgate or the sunroof is open.

OSP2I049116E

OSP2I049117

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments