manualshive.com logo in svg

Kia SELTOS, Manual, Page: 159 / 280

Share
Download
Kia SELTOS Manual Download Page 159

67

4

4

Features of your vehicle

LCD displays

Transmission temperature (dual 
clutch transmission) (if equipped)

This mode displays the transmission 
temperature.

Digital speedometer

This digital speedometer display 
shows the speed of the vehicle.

Service mode

This mode reminds you of scheduled 
maintenance information.

Service in

It calculates and displays when you 
need a scheduled maintenance ser

-

vice (mileage or days).

If the remaining mileage or time 
reaches 1,500 km (900 miles) or 30 
days, "Service in" message is dis

-

played for several seconds each 
time you set the ignition switch or 
ENGINE START/STOP button to the 
ON position.

Service required

If you do not have your vehicle ser

-

viced according to the already 
inputted service interval, "Service 
required" message is displayed for 
several seconds each time you set 
the ignition switch or ENGINE 
START/STOP button to the ON posi

-

tion.

To reset the service interval to the 
mileage and days you inputted 
before:
䳜 Press the OK button (Reset) for 

more than 1 second.

OSP2I049113E

OSK3048331CR

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments