Kia SELTOS Manual Download Page 158

Page: 158 / 280

Features of your vehicle

LCD displays

Accumulated driving information
mode

This display shows the accumulated
trip distance (1), the average fuel
efficiency (2), and the total driving
time (3).

䳜 Accumulated information is calcu

lated after the vehicle has run for
more than 300 metres.

䳜 If you press "OK" button for more

than 1 second after the Cumula

tive Information is displayed, the
information will be reset.

䳜 If the engine is running, even

when the vehicle is not in motion,
the information will be accumu

lated.

Drive Info display

This display shows the trip distance
(1), the average fuel efficiency (2),
and the total driving time (3) infor

mation once per one ignition cycle.

䳜 Fuel efficiency is calculated after

the vehicle has run for more than
300 metres.

䳜 The Driving Information will be

reset 4 hours after ignition has
been turned off. So, when the
vehicle ignition is turned on within
4 hours, the information will not
be reset.

䳜 If you press "OK" button for more

than 1 second after the Driving
Information is displayed, the
information will be reset.

䳜 If the engine is running, even

when the vehicle is not in motion,
the information will be accumu

lated.

OSP2I049114E

OSP2I049116E

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 158 / 280

Search results

Summary of Contents for SELTOS

Reviews: