manualshive.com logo in svg

Kia SELTOS, Manual, Page: 149 / 280

Share
Download
Kia SELTOS Manual Download Page 149

57

4

4

Features of your vehicle

LCD display

Trip computer mode

The trip computer mode displays 
information related to vehicle driv

-

ing parameters including fuel econ

-

omy, tripmeter information and 
vehicle speed.

* For more details, refer to "Trip 

information (trip computer)" on 
page 4-64.

Turn By Turn (TBT) mode

This mode displays the state of the 
navigation.

Driving Assist mode

This mode displays the state of:
䳜 Smart Cruise Control (if equipped)
䳜 Lane Safety system (if equipped)
䳜 Driver Attention Warning (if 

equipped)

䳜 AWD (if equipped)
䳜 Tyre pressure

* For more details, refer to each 

system information in "Driving 
your vehicle" on page 6-6.

Tyre pressure status

* For more details, refer to "Tyre 

Pressure Monitoring System 
(TPMS) (if equipped)" on page 7-
10.

OSP2I049111E

OSP2I049112

OSP2049138E

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments