manualshive.com logo in svg

Kia SELTOS, Manual, Page: 135 / 280

Share
Download
Kia SELTOS Manual Download Page 135

43

4

4

Features of your vehicle

Steering wheel

NOTICE

After adjustment, sometimes the 
lock-release lever may not lock the 
steering wheel.
It is not a malfunction. This occurs 
when two gears engage. In this 
case, adjust the steering wheel 
again and then lock the steering 
wheel.

Heated steering wheel (if equipped)

When the ignition switch is in the 
ONPosition or the ENGINE START/
STOP button in the ON position, 
pressing the heated steering wheel 
button warms the steering wheel. 
The indicator on the button will illu

-

minate.

To turn the heated steering wheel 
off, press the button once again. 
The indicator on the button will turn 
off.

NOTICE

The heated steering wheel will turn 
off automatically approximately 30 
minutes after the heated steering 
wheel is turned on.

CAUTION

䳜 Do not install any type of grip 

cover for the steering wheel, it 
may impair the function of the 
heated steering wheel system.

䳜 When cleaning the heated steer

-

ing wheel, do not use an organic 
solvent such as paint thinner, 
benzene, alcohol and petrol. Doing 
so may damage the surface of 
the steering wheel.

䳜 If the surface of the steering 

wheel is damaged by a sharp 
object, damage to the heated 
steering wheel components could 
occur.

WARNING

If the steering wheel becomes too 
warm, turn the system off. The 
heated steering wheel may cause 
burns even at low temperatures, 
especially if used for long periods of 
time.

OSP2049012R

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments