manualshive.com logo in svg

Kia SELTOS, Manual, Page: 124 / 280

Share
Download
Kia SELTOS Manual Download Page 124

Features of your vehicle

32

4

Bonnet

2. Go to the front of the vehicle, 

raise the bonnet slightly, push the 
secondary latch (1) up side and lift 
the bonnet (2).

3. Pull out the support rod.

4. Hold the bonnet opened with the 

support rod.

Bonnet open warning

The bonnet warning message will 
appear on the LCD display when 
bonnet is open.

The warning chime will operate 
when the vehicle is being driven at 
or above 3 km/h (2 mph) with the 
bonnet open.

Closing the bonnet

1. Before closing the bonnet, check 

the following:
䳜 All filler caps in the engine com

-

partment must be correctly 
installed.

䳜 Gloves, rags or any other com

-

bustible material must be 
removed from the engine com

-

partment.

2. Lower the bonnet halfway 

(approximately 30 cm) and push 
down to securely lock in place.

3. Check that the bonnet has 

engaged properly.
䳜 If the bonnet can be raise 

slightly, it is not properly 
engaged.

OSP2041007R

OSP2041076R

OSP2049102

Summary of Contents for SELTOS

























































































































































































































































































Reviews:

No comments