Kia SELTOS Manual Download Page 105

Page: 105 / 280

Features of your vehicle

Smart key

Battery replacement

The transmitter or smart key uses a
3 volt lithium battery which will nor

mally last for several years.

When replacement is necessary, use
the following procedure.
1. Insert a slim tool into the slot and

gently pry open the transmitter
or smart key cover.

2. Replace the battery with a new

battery (CR2032). When replac

ing the battery, make sure the
battery position.

3. Install the battery in the reverse

order of removal.

For transmitter or smart key
replacement, Kia recommends to
visit an authorised Kia dealer/ser

vice partner.

WARNING

THIS PRODUCT CONTAINS A BUT

TON BATTERY
If swallowed, a lithium button bat

tery can cause severe or fatal inju

ries within 2 hours.

Keep batteries out of reach of chil

dren. If you think batteries may
have been swallowed or placed
inside any part of the body, seek
immediate medical attention.

CAUTION

䳜 The keyless entry system trans

mitter is designed to give you
years of trouble-free use, how

ever it can malfunction if exposed
to moisture or static electricity. If
you are unsure how to use or
replace the battery, Kia recom

mends to contact an authorised
Kia dealer/service partner.

䳜 Using the wrong battery can

cause the transmitter or smart
key to malfunction. Be sure to use
the correct battery.

䳜 To avoid damaging the transmit

ter or smart key, don't drop it, get
it wet, or expose it to heat or
sunlight.

CAUTION

An inappropriately dis

posed battery can be
harmful to the environ

ment and human health.

Dispose the battery according to
your local law(s) or regulation.

OBDC049032RE

Summary of Contents for SELTOS

























































































































































































































































































Search results

Summary of Contents for SELTOS

Reviews:

Kia SELTOS, Manual, Page: 105 / 280

Search results

Summary of Contents for SELTOS

Reviews: