manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 499 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 499

9

8

8

Specifications, Consumer information 
and Reporting safety defects

Vehicle identification number (VIN)

Vehicle identification number 
(VIN)

The vehicle identification number (VIN) 
is the number used in registering your 
vehicle and in all legal matters pertain

-

ing to its ownership, etc.

Frame number

The number is punched on the floor 
under the passenger seat. To check the 
number, open the cover.
The VIN is also on a plate attached to the 
top of the dashboard. The number on 
the plate can easily be seen through the 
windshield from outside.

VIN label (if equipped)

Vehicle certification label

The vehicle certification label attached 
on the driver’s (or front passenger’s) 
side center pillar gives the vehicle identi

-

fication number (VIN).

OBD081002

OJA080002L

OST087005

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments