manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 479 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 479

69

7

7

Maintenance

Light bulbs

High mounted stop lamp (LED 
type) bulb replacement

If the high mounted stop lamp (1) does 
not operate, have the vehicle checked 
by an authorized Kia dealer.

Map lamp (Bulb type) bulb 
replacement

WARNING

Prior to working on the Interior lamps, 
ensure that the “OFF” button is 
depressed to avoid burning your fingers 
or receiving an electric shock.

1. Using a flat-blade screwdriver, gently 

pry the lens cover from lamp housing.

2. Remove the bulb by pulling it straight 

out.

3. Install a new bulb in the socket.
4. Align the lens cover tabs with the 

lamp housing notches and snap the 
lens into place.

CAUTION

Be careful not to dirty or damage the 
lens, lens tab, and plastic housings. 
Allow the bulb to cool down before han

-

dling it.

Map lamp (LED type) bulb 
replacement

If the map lamp (LED) (1), does not oper

-

ate, have the vehicle checked by an 
authorized Kia dealer.
The LED lamps cannot be replaced as a 
single unit because it is an integrated 
unit. The LED lamps has to be replaced 
with the unit.
A skilled technician should check or 
repair the map lamp (LED), for it may 
damage related parts of the vehicle.

OBD071132N

OBD071056

OBD071057

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments