manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 477 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 477

67

7

7

Maintenance

Light bulbs

5. Insert a new bulb by inserting it into 

the socket and rotating it until it locks 
into place.

6. Install the socket in the assembly by 

aligning the tabs on the socket with 
the slots in the assembly. Push the 
socket into the assembly and turn the 
socket clockwise.

7. Install the liftgate lid cover.

Stop and tail lamp (LED type) 
bulb replacement

Rear combination lamp - Type B

If the stop (1) and tail (2) lamp (LED), 
does not operate, have the vehicle 
checked by an authorized Kia dealer.
The LED lamps cannot be replaced as a 
single unit because it is an integrated 
unit. The LED lamps has to be replaced 
with the unit.
A skilled technician should check or 
repair the stop and tail lamp (LED), for it 
may damage related parts of the vehicle.

Side marker (LED type) bulb 
replacement

Rear combination lamp - Type B

If the side marker (LED) (1) does not 
operate, have the vehicle checked by an 
authorized Kia dealer. The LED lamp 
cannot be replaced as a single compo

-

nent because it is an integrated unit. The 
LED lamp has to be replaced with the 
unit. A skilled technician should check or 
repair the side marker (LED), for it may 
damage related parts of the vehicle.

Rear turn signal lamp (Bulb type) 
bulb replacement

If the rear turn signal lamp (1) does not 
operate, have the vehicle checked by an 
authorized Kia dealer.

OBD071214N

OBD071195N

OBD078128L

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments