manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 475 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 475

65

7

7

Maintenance

Light bulbs

Front fog lamp (LED type) bulb 
replacement

If the front fog lamp (LED) (1), does not 
operate, have the vehicle checked by an 
authorized Kia dealer. The LED lamps 
cannot be replaced as a single unit 
because it is an integrated unit. The LED 
lamps has to be replaced with the unit.A 
skilled technician should check or repair 
the front fog lamp (LED), for it may dam

-

age related parts of the vehicle.

Side repeater lamp (LED type) 
bulb replacement

If the side repeater lamp (LED) (1) does 
not operate, have the vehicle checked 
by an authorized Kia dealer.The LED 
lamp cannot be replaced as a single 
component because it is an integrated 

unit. The LED lamp has to be replaced 
with the unit.A skilled technician should 
check or repair the side repeater lamp 
(LED), for it may damage related parts of 
the vehicle. 

Stop and tail lamp/side marker 
(Bulb type) bulb replacement

Rear combination lamp - Type A

1. Open the liftgate.
2. Loosen the light assembly retaining 

screws with a cross-tip screwdriver. 

3. Remove the rear combination lamp 

assembly from the body of the vehi

-

cle.

4. Disconnect the rear combination lamp 

connector. 

OBD071211

OBD071038

OBD071047L

OBD071047

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments