manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 430 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 430

Maintenance

20

7

Checking fluid levels

age. Replace any damaged parts and, if 
necessary, repack the grease.

Air conditioning refrigerant

Check the air conditioning lines and con

-

nections for leakage and damage.

Checking fluid levels

When checking engine oil, engine cool

-

ant, brake fluid, and washer fluid, always 
be sure to clean the area around any 
filler plug, drain plug, or dipstick before 
checking or draining any lubricant or 
fluid. This is especially important in 
dusty or sandy areas and when the vehi

-

cle is used on unpaved roads. Cleaning 
the plug and dipstick areas will prevent 
dirt and grit from entering the engine 
and other mechanisms that could be 
damaged.

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments