Kia FORTE 2022 Manual Download Page 396

Page: 396 / 514

What to do in an emergency

If you have a flat tire (with spare tire)

Jack label

Example

Type A

Type B

Type C

* The actual Jack label in the vehicle may differ from the illustration. For more

detailed specifications, refer to the label attached to the jack.

1. Model Name
2. Maximum allowable load
3. When using the jack, set your parking

brake.

4. When using the jack, stop the engine.
5. Do not get under a vehicle that is sup

ported by a jack.

6. The designated locations under the

frame

7. When supporting the vehicle, the base

plate of jack must be vertical under
the lifting point.

8. Move the shift lever to the P position

on vehicles with Intelligent Variable
Transmission.

9. The jack should be used on firm level

ground.

10.Jack manufacturer
11.Production date
12.Representative company and address

OHYK064001

OHYK064005

OHYK064002

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Search results

Summary of Contents for FORTE 2022

Reviews:

Kia FORTE 2022, Manual, Page: 396 / 514

Search results

Summary of Contents for FORTE 2022

Reviews: