manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 309 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 309

99

5

5

Driving your vehicle

Cruise Control (CC)

Cruise Control (CC) (if 
equipped)

(1) Cruise indicator
(2) Set speed
Cruise Control will allow you to drive at 
speeds above 30 km/h (20 mph) without 
depressing the accelerator pedal.

Cruise Control Operation

Setting set speed

1. Accelerate to the desired speed, 

which must be more than 30 km/h 
(20 mph).

2. Press the Driving Assist button at the 

desired speed. The set speed and 
Cruise (

) indicator will illu

-

minate on the cluster.

3. Release the accelerator pedal.

Vehicle speed will maintain the set 
speed even when the accelerator 
pedal is not depressed.

NOTICE

On a steep slope, the vehicle may 
slightly slow down or speed up while 
driving uphill or downhill.

Increasing set speed

僅 Push the + switch up and release it 

immediately. The set speed will 
increase by 1 km/h (1 mph) each time 
the switch is operated in this manner.

僅 Push the + switch up and hold it while 

monitoring the set speed on the clus

-

ter. The set speed will increase to the 
nearest multiple of ten (multiple of 
five in mph) at first, and then increase 
by 10 km/h (5 mph) each time the 
switch is operated in this manner.
Release the switch when the desired 
speed is shown and the vehicle will 
accelerate to that speed.

OBD051384L

OBDM051369

OBD051371

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments