manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 265 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 265

55

5

5

Driving your vehicle

Forward Collision–Avoidance Assist (FCA) (Front view camera

only)

depending on the road conditions and 
the surroundings.

WARNING

僅 Even if there is a problem with For

-

ward Collision-Avoidance Assist, the 
vehicle's basic braking performance 
will operate properly.

僅 During emergency braking, braking 

control by Forward Collision-Avoid

-

ance Assist will automatically cancel 
when the driver excessively depresses 
the accelerator pedal or sharply steers 
the vehicle.

CAUTION

Depending on the condition of the vehi

-

cle, pedestrian in front and the sur

-

roundings, the speed range to operate 
Forward Collision-Avoidance Assist may 
reduce. The function may only warn the 
driver, or the function may not operate.

NOTICE

In a situation where a collision is immi

-

nent, braking may be assisted by For

-

ward Collision-Avoidance Assist when 
braking is insufficient by the driver.

Forward Collision-Avoidance 
Assist Malfunction and Limita

-

tions

Forward Collision-Avoidance 
Assist Malfunction

When Forward Collision-Avoidance 
Assist is not working properly, the 
'Check Forward Safety system' warning 
message will appear (turns off after a 

certain time), and the 

 and 

 

warning lights will illuminate on the clus

-

ter. In this case, have the vehicle 
inspected by an authorized Kia dealer.

Forward Collision-Avoidance 
Assist disabled

OMQ4050074L

OMQ4050073L

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments