Home
/
Kia
/
FORTE 2022
/
Manual

Kia FORTE 2022, Manual, Page: 182 / 514

Share

Page: 182 / 514

Kia FORTE 2022 Manual Download Page 182

Features of your vehicle

106

4

Automatic climate control system

Automatic climate control system (if equipped)

The automatic climate control system uses cooling and heating to help maintain a
pleasant environment inside the vehicle.

1. Driver’s temperature control knob
2. AUTO (automatic control) button
3. Front windshield defroster button
4. Rear window defroster button
5. Air conditioning button
6. Air intake control button
7. Blower OFF button
8. Fan speed control button
9. Mode selection button
10.Passenger’s temperature control knob
11.SYNC button
12.A/C display

NOTICE

Operating the blower when the ignition switch or ENGINE START/STOP button is in
the ON position could cause the battery to discharge. Operate the blower when the
engine is running.

OBD041312N

«
...
180
181
182
183
184
...
»

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments