manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 112 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 112

Features of your vehicle

36

4

Hood

Hood open warning

The hood warning message will appear 
on the LCD display when hood is open.

The warning chime will operate when 
the vehicle is being driven at or above 3 
km/h (2 mph) with the hood open.

Closing the hood

1. Before closing the hood, check the 

following:
僅 All filler caps in the engine com

-

partment must be correctly 
installed.

僅 Gloves, rags or any other combusti

-

ble material must be removed from 
the engine compartment.

2. Return the support rod to its clip to 

prevent it from ratting.

3. Lower the hood until it is about 30 cm 

(12 inches) above the closed position 
and let it drop. Make sure that it locks 
into place.

4. Check that the hood has engaged 

properly.
僅 If the hood can be raise slightly, it is 

not properly engaged.

僅 Open it again and close it with a lit

-

tle more force.

CAUTION

Hood obstruction

Before closing the hood, ensure that all 
obstructions are removed from the hood 
opening. Closing the hood with an 
obstruction present in the hood opening 
may result in property damage.

WARNING

Fire risk

Do not leave gloves, rags or any other 
combustible material in the engine com

-

partment. Doing so may cause a heat-
induced fire.

WARNING

Unsecured engine hood

Always double check to be sure that the 
hood is firmly latched before driving 
away. If it is not latched, the hood could 
fly open while the vehicle is being driven, 

OBD041540

OBD041678N

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments