manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 111 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 111

35

4

4

Features of your vehicle

Hood

Hood

The hood serves as a cover for the 
engine compartment.
Open the hood if maintenance work 
needs to be performed in the engine 
compartment or if you need to look at 
the compartment.

Opening the hood

1. Pull the release lever to unlatch the 

hood. The hood should pop open 
slightly.

Open the hood after turning off the 
engine on a flat surface, shifting the 
shift lever to the P (Park, for Dual 
Clutch Transmission/ Intelligent Vari

-

able Transmission) or first gear or R 
(Reverse, for Manual Transmission) 
and set the parking brake.

2. Go to the front of the vehicle, raise the 

hood slightly, push the secondary 
latch (1) up side and lift the hood (2).

3. Pull out the support rod.
4. Hold the hood opened with the sup

-

port rod(3).

WARNING

Hot parts

Grasp the support rod in the area 
wrapped in rubber. The rubber will help 
prevent you from being burned by hot 
metal when the engine is hot.

OBD041048

OBD041049

OBD041086

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments