manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 434 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 434

Maintenance

24

7

Engine coolant

The coolant level should be filled 
between F and L (or MAX and MIN) 
marks on the coolant level gauge when 
the engine is cool.
If the coolant level is low, add enough 
specified coolant to provide protection 
against freezing and corrosion. Bring the 
level to F (or MAX), but do not overfill. If 
frequent additions are required, see an 
authorized Kia dealer for a cooling sys

-

tem inspection.

NOTICE

Make sure the coolant cap is properly 
closed after refill of coolant.
Otherwise the engine could be over

-

heated while driving.

1. Check if the radiator cap label is on 

straight.

Engine room front view

2. Make sure that the tiny protrusions 

inside the coolant cap are securely 
interlocked.

Engine room rear view

Recommended engine coolant

僅 When adding coolant, use only deion

-

ized water or soft water for your vehi

-

cle and never mix hard water in the 
coolant filled at the factory. An 
improper coolant mixture can result in 
serious malfunction or engine dam

-

age.

僅 The engine in your vehicle has alumi

-

num engine parts and must be pro

-

tected by an ethylene-glycol with 
phosphate based coolant to prevent 
corrosion and freezing.

僅 DO NOT USE alcohol or methanol 

coolant or mix them with the specified 
coolant.

僅 Do not use a solution that contains 

more than 60% antifreeze or less than 
35% antifreeze. This would reduce the 
effectiveness of the solution.

OJA070150L

OBD071134

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments