manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 426 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 426

Maintenance

16

7

Scheduled maintenance service

Maintenance Under Severe Usage Conditions - Non Turbo Models

The following items must be serviced more frequently on cars mainly used under 
severe driving conditions. Refer to the chart below for the appropriate maintenance 
intervals.

R: Replace
I: Inspect and if necessary, adjust, correct, clean or replace

Maintenance item

Maintenance 

operation

Maintenance intervals

Driving condition

Engine oil and 
engine oil filter

(Gaso

-

line) 2.0 
MPI

R

Every 6,000 km (3,750 

miles) or 6 months

A, B, C, D, E, F, G, H, I, 

J, K

Intelligent Variable Trans

-

mission (IVT) fluid

R

91,000 km (56,000 

miles)

A, C, E, F, G, H, I, K

Air cleaner filter

R

More frequently

C, E

Spark plugs

R

More frequently

A, B, F, G, H, I, K

Climate control air filter

I

More frequently

C, E, G

Parking brake

I

More frequently

C, D, G, H

Brake discs, pads and cali

-

pers

I

More frequently

C, D, E, G, H, J, K

Suspension ball joints and 
mounting bolts

I

More frequently

C, D, E, F, G

Steering gear rack, linkage 
and boots

I

More frequently

C, D, E, F, G

Drive shafts and boots

I

More frequently

C, D, E, F, G, H, I, J

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments