manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 343 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 343

133

5

5

Driving your vehicle

Rear Cross-Traffic Collision-Avoidance Assist (RCCA)

僅 To warn the driver of an approaching 

vehicle from the rear left/right side of 
your vehicle, the warning light on the 
side view mirror will blink and a warn

-

ing message will appear on the clus

-

ter. At the same time, an audible 
warning will sound.

僅 Rear Cross-Traffic Collision-Avoid

-

ance Assist will operate when the fol

-

lowing conditions are satisfied:
- Your vehicle gear is shifted to R 

(Reverse)

- Your vehicle speed is below 8 km/h 

(5 mph)

- The approaching vehicle is within 

approximately 25 m (82 ft.) from 
the left or right side of your vehicle

- The speed of the vehicle approach

-

ing from the left or right side is 
above 5 km/h (3 mph)

NOTICE

If the operating conditions are satisfied, 
there will be a warning whenever the 
vehicle approaches from the left or right 
side even though your vehicle speed is 0 
km/h (0 mph).

Emergency Braking

OBD041269

OBDM041676

OBD051385L

OBD041246L

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments