manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 340 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 340

Driving your vehicle

130

5

Rear Cross-Traffic Collision-Avoidance Assist (RCCA)

adjacent to general roads or nearby 
roads exist in a parallel way)

CAUTION

For more details on the limitations of the 
front view camera, front radar, refer to 
"Forward Collision-Avoidance Assist 
(FCA) (Sensor fusion) (if equipped)" on 
page 5-61.

This device complies with Indus

-

try Canada licence-exempt RSS 
standard(s).

Operation is subject to the following 
conditions:
1. This device may not cause interfer

-

ence, and

2. This device must accept any interfer

-

ence, including interference that may 
cause undesired operation of the 
device.

3. Changes or modifications not 

expressly approved by the party 
responsible for compliance could void 
the user's authority to operate the 
device. 

Rear Cross-Traffic Collision-
Avoidance Assist (RCCA)

Rear Cross-Traffic Collision-Avoidance 
Assist is designed to detect vehicles 
approaching from the rear left and right 
side while your vehicle is reversing, and 
warning the driver that a collision is 
imminent with a warning message and 
an audible warning. Also, to help prevent 
collisions, braking assist may be applied.

[A]: Rear Cross-Traffic Collision Warning 
operating range
[B]: Rear Cross-Traffic Collision-Avoid

-

ance Assist operating range

CAUTION

Warning Timing may vary depending on 
vehicle speed of the approaching vehi

-

cle.

ODL3059072

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments